Honda Odyssey Service Manual: Rearview camera image does not change when selecting different views

Honda Odyssey Service Manual / Accessories / Driver Assist / Backup Camera / Rearview camera image does not change when selecting different views

NOTE:

  • Check the vehicle battery condition first.

  • You can select three different rearview camera angles for backing up. If there is no camera image on the display, go to Rearview camera image does not come on or work properly troubleshooting.

  • Check any official Honda service website for more service information about the navigation system.

  • Check the connectors for poor connections or loose terminals.

  1. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.

  2. Move the shift lever to R.

  3. Press the interface dial to see if the rearview image changes between the wide view, the normal view, and the top down view in this order.

  4. Does the rearview camera image change properly?

    YES —

    Intermittent failure, the system is OK at this time.¦


    NO —

    Go to step 4.


  1. Move the shift lever to P or N.

  1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

  1. Disconnect audio-navigation unit connector G (24P).

  1. Disconnect the rearview camera 12P connector.

  1. Check for continuity between body ground and audio-navigation unit connector G (24P) terminals No. 5   and No. 18 individually.

  2. 1 1 1 2 2 3 2 4 1 0 2 2 9 2 1 8 2 0 7 1 9 6 1 8 5 1 7 4 1 6 3 1 5 2 1 4 1 1 3 Wire side of female terminals?AUDIO-NAVIGATION UNIT CONNECTOR G (24P)?CAMERA BIT 0 (ORN)??CAMERA BIT 1 (BRN)

    Is there continuity?

    YES —

    Repair a short to body ground in the wire(s) between the audio-navigation unit   and the rearview camera.¦


    NO —

    Go to step 9.


  1. Check for continuity between audio-navigation unit connector G (24P) terminals No. 5 and No. 18.

  2. 1 1 1 2 2 3 2 4 1 0 2 2 9 2 1 8 2 0 7 1 9 6 1 8 5 1 7 4 1 6 3 1 5 2 1 4 1 1 3 Wire side of female terminalsAUDIO-NAVIGATION UNIT CONNECTOR G (24P)?CAMERA BIT 1 (BRN)CAMERA BIT 0 (ORN)

    Is there continuity?

    YES —

    Repair a short in the wires between the audio-navigation unit   and the rearview camera.¦


    NO —

    Go to step 10.


  1. Check for continuity between audio-navigation unit connector G (24P) terminals No. 5 and No. 18 and rearview camera 12P connector terminals No. 7 and No. 8   respectively.

  2. 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1 2 4 2 3 2 2 2 1 2 0 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 ??Terminal side of male terminalsWire side of female terminalsREARVIEW CAMERA 12P CONNECTORCAMERA BIT 1 (BRN)AUDIO-NAVIGATION UNIT CONNECTOR G (24P)CAMERA BIT 0 (ORN)CAMERA BIT 1 (BRN)CAMERA BIT 0 (ORN)

    Is there continuity?

    YES —

    Go to step 11.


    NO —

    Repair an open in the wire(s) between the audio-navigation unit   and the rearview camera.¦


  1. Substitute a known-good rearview camera.

  1. Reconnect all the connectors, and recheck.

  2. Does the symptom go away?

    YES —

    Replace the original rearview camera.¦


    NO —

    Replace the audio-navigation unit.¦


    Backup Camera

    Rearview Camera Removal/Installation (With Navigation)

    See More:

    Honda Odyssey Service Manual > Blind Spot Monitor: Blind Spot Information System (BSI)   Radar Unit Inputs and Outputs
    1 2 3 4 5 6 Terminal side of female terminalsLEFT SIDE BSI RADAR UNIT 6P CONNECTOR Terminal number Wire color Terminal name Description Signal 1 LT GRN IG1 ECU RR(7.5A) Power supply for the BSI radar unit Vehicle in ON mode: Battery voltage Vehicle in OFF mode: About 0 V 2 RED DR BSI IND+ Drives th ...

    Honda Odyssey Owners Manual

    Honda Odyssey Service Manual

    © 2018-2020 Copyright www.hodyssey.net
    0.0124